Multipoint Precision Fever Finder

Multipoint Precision Fever Finder

The Multi point Precision Fever Finder is ideal for fast and reliable fever temperature measurement. Unlike thermal

imaging cameras, the F uses germanium sensors from Germany that can accurate measure to a +0.4°C tolerance with 0.1°C resolution

The F has 14 infrared sensors aligned from top to bottom, ensuring the ability to cater for different heights of people from children to adults. The sensors will take the maximum temperature from any exposed part of the body. Due to the proximity of the sensors, the F has an effective operating distance to the target of around 20-40cm, hence the measurement repeatability is greatly improved

The entire system only needs minutes to set up and most of the parameters are already factory adjusted. The FF38 only requires a 220V power source for operation. An optional large LED monitor can be supplied with the F F38 to improve readability of temperature from larger distances (6cm red bright LED) and an audio alarm will automatically set off when a feverish condition is detected

TECHNICAL SPECIFICATION

1. Detector: Germanium Type from germany
2. No Of Detector sensor: 14 Point
3. Temperature range: 33C - 43C
4. Resolution: 0.1C
5. Accuracy: +/-0.4C
6. Repeatibilty: +/-0.2C
7. Effective Operating Distance: 20-40 cm
8. Operating Temperature: 20-28C
9. Operating Humidity: 85%
10. Measuring Time: ≤1s
11. Power Supply: Adaptor 9VDC, 500mA
12. Height of the Unit: 1500mm - 2200mm
13. Size: (1500-2200)x360x520mm
14. Weight: 15Kgs

FAQ FF38

1. What is the main difference between thermal imaging cameras and the Fever Finder 38? The tolerance of general thermal imaging cameras is +2°C (+2%) while the FF38 features a tolerance of +0.4°C (33 - 37°C). In general, normal thermal cameras have poor repeatabi(ity. Scanning over massive targets.
2. Which system is better? The FF38 or the thermal camera? Thermal cameras scan over massive targets. However FF38 scans each individual with precision. So thermal cameras are better for larger, moving targets whereas the FF38 is better for one to one operation.
3. Can both the thermal camera and FF38 be used together on site?Yes, ideally they complement each other. The thermal camera is served as a first defence gate and the FF38 is then used to confirm the feverish condition with more accuracy.
4. How about the investment cost? A proper fever thermal camera is normally much more expensive than the F.
5. Is the FF38 difficult to setup andoperate? No! There is no need for users to manually set up anything as the FF38 is delivered factory adjusted. Computers are not required for operation at all. For basic local monitoring, you only need to plug the FF38 into the wall power outlet and it is ready to go. Minimum supervision is required. However, users still can alter the alarm temperature and offset temperature through the local monitor located on the unit.
6. Does IRTEK have both systems? (thermal camera and FF38) Yes!
7. Would I still need a portable  infrared  thermometer  if  I  have  the  FF38? No, the FF38 replaces the infrared thermometer without operator intervention and human error.
8. If I need the precision of the FF38 but also a fast enough operating speed to save queueing time, what is the solution? You can invest in more units of FF38 to save a lot of queuing time. You can invest in say five to six units to achieve the speed and accuracy of a 50Hz thermal imaging fever camera whilst still being cheaper than the camera.
9. Is there any training required to operate the FF38? Unlike the thermal imaging camera where some basic training is required, the FF38 needs absolutely no training.
10. If I install a few units of the FF38, can we monitor the temperature from a laptop computer we place in a control room? Not at the moment. We are still working on the control software but all the hardware such as USB connection, RS485 and Wi-Fi is already installed in the standard configuration. You will only need to purchase the software when it is available.

Apa bedanya scan dgn IR gun dan sistem scanner.                     

1. Mengurangi kontak dekat antara operator dan visitors                    
2. Tidak ada human error karena secara otomatis akan membaca suhu maksimum dari semua bagian tubuh 
3. Mengurangi keletihan operator sehingga pembacaan tetap konsisten.      
4. Menghindari ketidak disiplinan  operator ( anda bisa lihat bagian Xray machine yg ada di pintu masuk mall untuk x ray tas yg sering asal asalan ) Bila ada satu target yg kelewat saja akan fatal                                                  
5. Tidak tergantung batere spt type gun , sebab batere yg sdh mulai lemah akan membuat akurasi pengukuran menurun.                
6. Salah target bagian tubuh yg di scan : Kalau anda lihat tayangan TV sering bukan jidat yg di ukur kadang di leher dan kadang di pergelangan tangan dan ada operator merasa tidak sopan menembak ke dahi

Hubungi Kami

PT.TRIAS NATHOMI CHEMINDO

Jakarta

Jalan Industri KAV 9-11 Komplek GK Blok SB No 3

Jakarta Pusat , Kemayoran 10710

Telp: 0812-708-68021

Batam

Komplek Ruko Taman Niaga Blok K No 11

Batam Centre

Telp: 0812-708-68021

Produk Terbaru Lainnya: